Product Details
Z-Tech Series 6-A Gray Head and Neck Restraint by Zamp® Color: Gray. The new Series 6A has new features never seen before in the Head and Neck Restraint market. These new Patent Pending.
Specifications
| Color: Gray |
Features
- 02 Spring Clip Quick Connect makes it even easier to connect or disconnect the device from the helmet
- Advanced Axis Adjustment allows you to adjust shoulder width, arm angle and arm width. Fits different body shapes and sizes through adjustments and works for different race seat configurations
- Aramid Fiber Webbing Tether connects helmet to restraint and offers good side to side motion during use
- Belt Channel with Wings accepts 2” or 3” belts
- Dual Compound Frame Specialized Fiberglass Reinforced Nylon is used for the shoulder frame offering leading structural characteristics. Arms made with a Modified Alloy material give the device a dampening characteristic in a crash. The two materials work together offering excellent performance
- Extremely Comfortable feels like you have nothing on
- HIGH- Back provides more natural pull angle and easier side to side movement
- Helmet Hardware needed is included to connect to one helmet.
- Replaceable Padding is easy to clean and/or replace for continued comfort
- SFI 38.1 Certified
- Stainless Steel Hardware screws and binary post built with high quality and strength to provide long lasting strength
- Super Lightweight at approximately 925 grams
Series 6-A Set Up :
Step 1 – Adjust the shoulder width adjustment
You will want to measure the width of your neck (diag. 1-A). The Series 1A has a neck width that ranges from 4.75 to 7.75 inches. Upon establishing that measurement, you will want to adjust your shoulder adjustment (diag. 1-B) to 1 inch wider than your neck measurement. Remove 4 screws and binary posts and set to correct position. If you will be adjusting wider than the setting out of the box, you may need to loosen the straps, video instructions./p>
Step 2 - Adjust the UPPER ARM Angle
It is recommended that you adjust this in your race seat to get the best angle for your individual needs. There are two screws on each side(diag. 2-A ). Screw #1 is the only screw that needs to be removed to adjust angle. Screw #2 does not need to be removed and it has thread lock on it from mfg. Remove Screw #1, and adjust the arm angle so that fits snug against body, but does not protrude into your body. Adjust both sides to same angle.
Step 3- Adjust the LOWER ARM Length
It is recommended that you adjust this in your race seat to get the best length for your individual needs. There are two screws on each side (diag. 3-A ). Remove both Screws. Adjust to a length that comfortably fits on your chest and in a position that allows the buckle from seat belts to tighten securely. The lower arm can be mounted inside or outside the upper arm.
Upon completion of steps 1-3, once you are 100% happy with the fit of your restraint, we recommend that at this time your remove all screws one at a time (except screw #2 in step 2) and secure them with tread lock “blue" and tighten snug.
Step 4 - Adjust tethers and strapping
It is recommended that you evaluate the video here in regards to adjustment of tethers and strapping. You will want to make sure the strapping stays in the same configuration throughout the hardware as you receive it from the mfg. There are two points which you will want to adjust (diag. 4-A). Point #1 should be adjusted to 2.75 inches (70mm) and Point #2 should be adjusted to approx. 1.75 inches (45mm).
Step 5 - Setting Up Helmet
Installation of Z-Tech hardware will depend on if your helmet has a certified M6 Insert or a Predrilled. Helmet inserts that are not certified are not recommended.
M6 Inserts – Set Part #2 against helmet shell centered to the insert. Then put the M6 Screw provided through Part #1 with thread lock “blue" on the end of the screw. Align Part #1 and M6 Screw through Part #2 and carefully screw the M6 insert into the helmet without cross threading during installation. Tighten snuggly and allow thread lock to dry.
Predrilled – You will 1st need to install Z-Tech nut washer Part #3 on the interior of the shell. Slide Part #3 between the Shell and EPS/Dense foam upper liner, carefully positioning it center to the predrilled hole. Once Part #3 is positioned correctly, then you can move on. Set Part #2 against helmet shell centered to the insert. Then put the M6 Screw provided through Part #1 with thread lock “blue" on the end of the screw. Align Part #1 and M6 Screw through Part #2 and carefully screw the M6 insert into the helmet without cross threading during installation. Tighten snuggly and allow thread lock to dry.
Zamp® is a foremost name in the field of head and neck protection. The company offers top-notch racing helmets, head and neck restraint, helmet shield retention kits, and more. Made utilizing leading-edge technology, Zamp products meet severe safety standards, including Snell SA2015, Snell M2015, SFI 38.1, SFI 24.1, and DOT. At every level of price point, the company offers the best value, features, and selection to meet or exceed your expectations. No matter whether you are a professional racer or a motorsports enthusiast, Zamp head and neck protection solutions are all you need to stay on the safe side.